The home is susceptible to the growth of molds especially if it is located in a location known to have high humidity levels. Some of the molds are usually poisonous and may affect the health of those inside the house. However, home owners can invest in a Mold Testing Illinois kit to help identify various facts about the molds.
The kits can either test the type of molds, if they are molds while others check both. As with the lift tape kits, they use a tacky and sticky surface to test the type of the molds. The tacky surface covers the sticky one which is placed onto the molds and then recovered by the tacky surface. The user then takes the tape to a laboratory where the exact type of molds is identified.
The next type of kit is used to check if there are molds. It includes a swab in a test tube and is names the instant kit. The swab is usually rubbed onto the surface that one suspect could be molds then returned into the tube. It is acceptable to set for approximately ten minutes then after that the owner can compare the color of the test tube with that presented in the color chart provided with the kit to analyze the results.
The viable kit is the next type. It is the most common type used as it shows the presence of the molds as well as its strain. The kit consists of a swab and petri dish that contains some gel inside it. The swab is wiped on the suspected molds then rubbed over the gel in the petri-dish dish. The dish is then closed and the molds are allowed to germinate from between 3 to 7 days.
Other than testing for molds, the viable kits are also used to test the quality of air in a house. This is achieved through using two kits which will have one of the petri dishes placed inside the house in one of the rooms and another placed outside the house but as close as possible to the room in which the other dish is placed. The dishes are opened for an hour then closed for 7days. The results should be similar; if not laboratory testing is necessary.
Heating and cooling systems are also tested by the same kits. One just needs to close all the vents of the system except one which is most far from the system itself where the kit is placed. On placing the kit, the system is made to run on high performance for about 10 minutes then stopped to remove the kit. It is later closed and left alone for 7 days to allow the molds that are present to grow so as to draw a conclusion.
It is important for each of these tests to involve a professional especially in checking the exact kind of molds that are being tested. The laboratories will easily identify these factors. It is important to know the kind of molds as some should not be removed by anyone as they are poisonous and will thus require experts to take care of them.
Molds have been known to lead to high allergies if left not contained with itchy skin and irritated eyes as a common sign of molds. For other people they tend to worsen their conditions example asthma.
The kits can either test the type of molds, if they are molds while others check both. As with the lift tape kits, they use a tacky and sticky surface to test the type of the molds. The tacky surface covers the sticky one which is placed onto the molds and then recovered by the tacky surface. The user then takes the tape to a laboratory where the exact type of molds is identified.
The next type of kit is used to check if there are molds. It includes a swab in a test tube and is names the instant kit. The swab is usually rubbed onto the surface that one suspect could be molds then returned into the tube. It is acceptable to set for approximately ten minutes then after that the owner can compare the color of the test tube with that presented in the color chart provided with the kit to analyze the results.
The viable kit is the next type. It is the most common type used as it shows the presence of the molds as well as its strain. The kit consists of a swab and petri dish that contains some gel inside it. The swab is wiped on the suspected molds then rubbed over the gel in the petri-dish dish. The dish is then closed and the molds are allowed to germinate from between 3 to 7 days.
Other than testing for molds, the viable kits are also used to test the quality of air in a house. This is achieved through using two kits which will have one of the petri dishes placed inside the house in one of the rooms and another placed outside the house but as close as possible to the room in which the other dish is placed. The dishes are opened for an hour then closed for 7days. The results should be similar; if not laboratory testing is necessary.
Heating and cooling systems are also tested by the same kits. One just needs to close all the vents of the system except one which is most far from the system itself where the kit is placed. On placing the kit, the system is made to run on high performance for about 10 minutes then stopped to remove the kit. It is later closed and left alone for 7 days to allow the molds that are present to grow so as to draw a conclusion.
It is important for each of these tests to involve a professional especially in checking the exact kind of molds that are being tested. The laboratories will easily identify these factors. It is important to know the kind of molds as some should not be removed by anyone as they are poisonous and will thus require experts to take care of them.
Molds have been known to lead to high allergies if left not contained with itchy skin and irritated eyes as a common sign of molds. For other people they tend to worsen their conditions example asthma.
About the Author:
Find a list of the benefits you get when you use mold testing Illinois services and more info about a reputable service provider at http://www.moldprochicago.com/moldprochicago.com/mold-services today.